![]() I don't know of a way of making it wired though and Artnet/sACN over wifi can be problematic. I have built a few WLED units and it does work well, however if left running for days the wifi sometimes stops working and needs reboot. For theatre use I'm not keen on wifi being used for control, but apparently there is a way of using wired ethernet in place of Wifi with these controllers. A related project is 'NodeMCU' which allows similar remote control of relays and triacs. One of the E1.31/Artnet control options offered allows preset scenes (and there's a big selection included by default) to be selected by DMX control value. I've started to play with it and I'm impressed. This is very much a DIY route, but the parts are small, cheap and easy to put in an suitable enclosure. The host microcontroller is an ESP32 or ESP8266 which has built in Wifi and costs around GBP10 from the usual online sources. Have a look at the 'WLED' project hosted on Github. I have been wanting to do simple DMX-controlled effects with LED pixel tape and run into the problems noted above. (Open and eager to learning it, but unfortunately can't dedicate a huge portion of time to it.)Īny help, recommendations, and suggestions will be greatly appreciated. Unfortunately I'm not experienced in the world of Arduino and coding etc. My current show controller features network functions so this could be a good solution for control/communication to the LED Tape. I've seen a few solutions that involve small Arduino controllers which looks like a potential solution. Finding an auto programme which does exactly what I'm after seems remarkably unlikely so I thought I'd come here in hope someone more experienced in intelligent LED Tape might be able to suggest some solutions as I'm currently going round in circles from google searching. My ideal solution is likely some form of intelligent RGB Tape which includes an auto programme that replicates what I'm after, that I can then turn on/off via a DMX Relay (would also require the fixture remembering settings on power cycle). Now when pixel mapping gets involved, naturally I lose a large number of DMX channels very quickly, which isn't ideal. The problem I'm facing is that I need this to integrate into my current show control system (Weigl ProCommander) which only features a single universe of DMX. Step 4: Run the Weigl Hardware Configurator Utility (Version 1.0 Production or higher) Step 5: Scan for devices Step 6: Note the IP Address after the scan. Obviously to do this I'll need some kind of intelligent RGB Tape and some kind of controller. (Please note that the ProCommander ES and ProCommander 1 / WEMC-1 units do not have device configuration settings and will have to be configured using the configurator steps below). To this day, the ProCommander VX is still the controller being used in the restaurants that still have animatronics.I'm currently working on a project in which I need some RGB LED tape to chase from one end of the tape to the other (and then repeat). The ProCommander VX had all the same features in the ProCommander LTC, but was intergraded with Weigl's own video player instead. In 2018 due to the concern of ageing hardware the ProCommander LTC's were replaced with Weigl's off the shelf controller the ProCommander VX. The ProCommander LTC was able to be controlled by Weigl's Embedded Linux Based POE touch panel and Weigl Mobile Commander smart phone app allowing staff to start shows with ease and allowed maintenance to easily put the system in diagnostic or maintenance mode. This was a big upgrade from the cyberstar system. ![]() This controller had an intergraded video player that was made by CE labs (this is a separate company not related to CEC Entertainment), controlled Audio, Video, Lighting, and animatronic movements via LTC (Linear Time Code) and used Weigl's pro I/O adapters to be able to control older animatronics. The first system that was implemented was a custom version of one of Weigl's controllers called the ProCommander LTC. ![]() The cyberstar was very outdated and was not very user friendly. Their pro commander series of animatronic controllers was the successor of the Cyberstar system in early 2012.ĭuring CEC's 5th redesign of the animatronic stage, CEC was looking for a more modern way to program and control their animatronics. Weigl Control is a manufacturer of animatronic, lighting and media controls.
0 Comments
Leave a Reply. |